[AMRadio] Home Brew

Brett gazdzinski Brett.gazdzinski at mci.com
Thu Sep 30 10:43:34 EDT 2004

Maybe, I would have to ask.

He and a friend bought a truck load of RCA iron, and its stored in his
I am not sure who has what iron left to sell, but I know he wants it out
of his garage.

It would be pick up only in South Jersey.
Price is around $200.00 I would guess, these are NEW transformers
in the original crates, although some have some surface rust after 50 years.
He has plenty of power transformers as well, but only 220 volt ones left
I think.

The mod trans would work very well with 813's into 813's.

I will call him and ask about the iron...


-----Original Message-----
From: amradio-bounces at mailman.qth.net
[mailto:amradio-bounces at mailman.qth.net] On Behalf Of Larry Roohr
Sent: Thursday, September 30, 2004 8:46 AM
To: Discussion of AM Radio
Subject: Re: [AMRadio] Home Brew

Hi Brett,

Would your friend with the full garage be interested in selling a mod 
transformer? I've been slowly gathering parts for an 2-813 by 2-813 
transmitter and would be interested if he is.



Brett gazdzinski wrote:

>A very good choice!
>Build it right, and it works like a Swiss watch, and is quiet, no fans
>or blowers needed. 250 to 300 watts out easy, with plenty of audio
>to go with the carrier.
>The tubes are easy to find and cheap, there were many surplus transformers
>that would power the setup nicely, mod transformer size is reasonable.
>Fair radio used to sell a Collins solder sealed power transformer that
>would give about 1000 volts at 600 ma full wave center tapped choke
>input, small size, 110 or 220 volt primary, used to go for $30.00!
>Variac it and it does 0 to 1500 volts, and will do the rf and mod decks
>if you want to keep things really simple.
>I have tried 812a's, 811a's, 572b's in the rf deck, and they all work
>fine and act the same as far as modulation, drive, and power output go.
>I have 3 old RCA mod transformers that work with this combo very well,
>and also work well with the pair of 813's and 4x150a's.
> 10,500 to 4350 ohms I think they are, and large!
>They are around, a friend has a garage full of them.
>I retired the cvm5, as the freq response was quite poor.
>Building a homebrew rig is incredibly fun, and quite a source of pride
>if you take the time to build it RIGHT so it works trouble free for
>years and years, and looks nice.
>To get parts, you have to network hams, look on ebay, go to fests,
>buy old homebrew pieces of crap for the parts, and use some of the
>vendors that sell rf stuff.
>Even building receivers has not been a problem for me, parts are around,
>you just have to dig for them instead of going to one place
>like in the old days.
>Often, the prices are very reasonable, I picked up a bunch of nice
>oil filled caps for $10.00 each at Gaithersburg fest last year.
>I got about 6 of them.
>They still make new ones, but they wanted $120.00 each!
>The two big fun points are the chassis chess part, where you
>Figure out just where things are going, and how you are going to keep
>things symmetrical, rf and front panel, and the initial testing.
>Building something, and firing it up and finding it works great
>is quite fun, and the fun continues every time you use the rig.
>It also gives plenty to talk about, there is not a lot to say
>about a rice box into an amp.
>Old vintage ham gear like Johnson 500, Collins 30k-1, globe king 400/500,
>and military surplus like the T368, art13, and others can be fun to play
>with, and sometimes turn up at reasonable prices (but not on ebay).
>80 meter night time is hard to break into, and needs good power
>levels, but 40 in the daytime is very friendly and you can do
>nicely with 100 watts and up.
>Valliant's, the Collins 32v series, dx100's, and others in that power class
>do very well on 40 meters, are fun to play with, and can be got
>at reasonable prices.
>People think they are expensive because they used to get them at fests
>for $10 or $20, but if you pay $500.00 for a 32v3, I think you got a lot
>of rig (and fun) for the money. The same money gets you an old crappy
>plastic rice box.
>Pay $3000.00 for a 30k-1 or some other bigger rig, and you have
>a lot of fun for the money, people spend that on little plastic
>boxes that put out 25 or 50 watts!
>For a lot of guys, playing with the equipment is as much
>fun as yakking into it.
>-----Original Message-----
>From: amradio-bounces at mailman.qth.net
>[mailto:amradio-bounces at mailman.qth.net] On Behalf Of John Coleman
>Sent: Tuesday, September 28, 2004 7:08 PM
>To: 'Discussion of AM Radio'
>Subject: RE: [AMRadio] Home Brew
>	If I were going to build with tubes again and two hundred watts was
>the carrier output that I wanted.  I would use a pair of 812s in push pull
>class C and modulate with a pair of 811As push pull class B.  Run about
>volts @ 200 ma for 300 watts plate input on the 812s.  Find a Modulation
>XFMR to match the output of 811A class B (about 12500 ohms as I remember)
>the 7500 ohm class C final. 
>John, WA5BXO
>AMRadio mailing list
>Home: http://mailman.qth.net/mailman/listinfo/amradio
>Help: http://mailman.qth.net/mmfaq.html
>Post: mailto:AMRadio at mailman.qth.net

AMRadio mailing list
Home: http://mailman.qth.net/mailman/listinfo/amradio
Help: http://mailman.qth.net/mmfaq.html
Post: mailto:AMRadio at mailman.qth.net

More information about the AMRadio mailing list

This page last updated 23 Feb 2018.