[AMRadio] NC-183D Alignment questions help


Van K7VS wa7fab at cdsnet.net
Wed Sep 26 19:57:56 EDT 2007


----- Original Message ----- 
From: "John Coleman" <jc at pctechref.com>
To: "'Discussion of AM Radio in the Amateur Service'" 
<amradio at mailman.qth.net>
Sent: Wednesday, September 26, 2007 3:55 PM
Subject: RE: [AMRadio] NC-183D Alignment questions help


Is the oscillator freq on the low end too high and needs to be lower or is
it to low and needs to be higher.

Some one mentioned that the oscillator may be running on the wrong side.
You may know this already but I will state it anyway, that the OSC must be
running above the RF that you want to receive.  OSC = RF + IF.  It is some
times possible to pull the OSC with the trimmer all the way down to where
the OSC = RF - IF.  This will work where you set it but it will not track as
the manufacture did not design it that way.

Assuming that the culprit is ageing coil forms, not incorrect parts or IF
misalignment, there could be a number of quick fixes for this type of thing.
Padding capacitors can be added in series with the top end of the coils or
extra turns could be added to the coil assembly or just placed in series
with it.  I have beat up some powdered iron and put it into the coil form
with glue to lower the frequency.

John, WA5BXO


-----Original Message-----
From: amradio-bounces at mailman.qth.net
[mailto:amradio-bounces at mailman.qth.net] On Behalf Of Van K7VS
Sent: Tuesday, September 25, 2007 11:04 PM
To: Discussion of AM Radio in the Amateur Service
Subject: [AMRadio] NC-183D Alignment questions help

I have a pristine NC-183D I picked up a year ago that I am finally getting
around to.  Have replaced all the electrolytics and sound really good.
BUT...I cannot get it to track properly as I follow the alignment
instructions in the manual.  I can set the top frequency on each band with a

small trimmer cap (this is the oscillator coil adjustment) but then
according to the instruction manual you adjust the low end of the dial by
moving a wire inside an inductor, which does move the lower frequency but
not nearly enough to get to the frequency they say you should see.  Has
anyone else had that problem during alignment of this receiver, or am I
missing something.  Have checked the voltages at the first and second
converter and they seem fine and have pulled off the mica cap across one of
the oscillator coils  (1.8 to 5 Mhz) and it checked just fine (supposed to
be 1600 pf and reads 1615 pf).  And have substituted a different 6BE6 in the

first converter and still can't get close to proper or accurate dial
tracking.  I am 500+ Khz off no matter what I have tried.  And thoughts on
this one!  Thanks.  Van, K7VS

PS  I would like to hear from NC-183D owners that may have experienced this
problem or have some thoughts about what I am seeing.  tnx

______________________________________________________________
Our Main Website: http://www.amfone.net
AMRadio mailing list
List Rules (must read!): http://w5ami.net/amradiofaq.html
List Home: http://mailman.qth.net/mailman/listinfo/amradio
Help: http://mailman.qth.net/mmfaq.html
Post: mailto:AMRadio at mailman.qth.net
To unsubscribe, send an email to amradio-request at mailman.qth.net with
the word unsubscribe in the message body.

______________________________________________________________
Our Main Website: http://www.amfone.net
AMRadio mailing list
List Rules (must read!): http://w5ami.net/amradiofaq.html
List Home: http://mailman.qth.net/mailman/listinfo/amradio
Help: http://mailman.qth.net/mmfaq.html
Post: mailto:AMRadio at mailman.qth.net
To unsubscribe, send an email to amradio-request at mailman.qth.net with
the word unsubscribe in the message body.


-- 
No virus found in this incoming message.
Checked by AVG Free Edition.
Version: 7.5.488 / Virus Database: 269.13.31/1031 - Release Date: 9/26/2007 
12:12 PM




More information about the AMRadio mailing list

This page last updated 23 Oct 2017.