[AMRadio] Kenwood Items FS


Ken, W8EK kenw8ek at gmail.com
Sat Jul 2 11:21:21 EDT 2016


Kenwood Items For Sale:

Plug In Crystal Filters, External Speaker, Desk Mics,
Dual Band Cross Band FM Transceiver, Multimode 2 M
Transceiver, Cables, Extension Feet, Etc.


Kenwood "Plug In" Crystal Filters:

All are for the 8.83 MHz IF, work 100% and look like new.
Paper work is included.

Kenwood YK-88 SN 1 Crystal Filter
This filter is 1800 Hz wide, for narrow SSB or wide CW/digital.
This is a "plug in filter" as opposed to the type that must
be soldered in. It is used in rigs such as the TS-450, TS-570,
TS-690, TS-850, TS-930, TS-940, TS-950, and others. $79

Kenwood YK-88 C 1 Crystal Filter
500 Hz wide for CW and narrow digital.
Fits same rigs as listed above. $79

Kenwood YK-88 S 1 Crystal Filter
This plug in filter is 2400 Hz wide and is used in the same
rigs as listed above. $75


Kenwood SP-23 External Speaker:

The Kenwood SP-23 base speaker matches many Kenwood
transceivers including the TS-450S, TS-570S/D and TS-690.
This versatile 8 ohm speaker features a metal cabinet with
flip-out tilt bar. It has a 3 inch (77 mm) speaker element
rated to 1 watt, with a 300 to 5000 Hz response. The rear
panel features two screw connections, and includes a 3 foot
audio cable.

It is 4.8 x 3.75 x 9.25 inches, and weighs 2.8 lbs.

This particular speaker works fine, and looks like new. It
is in its original box, with cable and paper work for only
$75.


Kenwood MC-60 A, Deluxe Desk Microphone:

The Kenwood MC-60A is a communication type dynamic unidirectional
mic. It features UP-DOWN tuning. The mic impedance may be set for
50K ohms or 500 ohms. The frequency response is 150 Hz to 10 kHz
(-6dB) with the Preamp off and 200 Hz to 7 kHz (-6 dB) with the
Preamp on. The heavy zinc die-cast base provides extra stability.
The mic terminates to a standard round 8 pin mic plug. It can be
used on virtually any of the Kenwood rigs that use a round 8 pin
connector. Please note that the earlier MC-60 (non-"A") version
has a 4 pin mic plug and no UP-DOWN tuning.

This particular mic appears to be new, unused. It came from a SK,
so I can not verify for sure, but it certainly looks new, and of
course works like new.

This is a current model and sells for about $160. Buy this one
for only $100.


Kenwood MC-85 Deluxe Desk Microphone Parts:

The Kenwood MC-85 will take up to three mic cords,
i.e. it is capable of being used on three rigs.

MC-85 desk mic "Tech Special"
It looks like the silent key was working on repair of this when
he passed. All parts appear to be present, plus the addition
of a couple extra up/down switches. $45


Kenwood TM-732 Dual Band FM Cross Band Repeat Transceiver:

The Kenwood TM-732A dual band 2 meter, 440 MHz transceiver
provides high performance communications with operating ease.
It features dual receive including V+V and U+U, built-in CTCSS,
DTSS and page functions, 50 memory channels and multi-scan
functions. The high visibility front panel is detachable.
Extended receive range is 118-174 MHz and 438-450 MHz. Power
output is 50/10/5 watts on 2 meters and 35/10/5 watts on 440
MHz. Requires 13.8 VDC at 11.5 amps. MC-45DM multifunction
DTMF hand mic included.

Features:
50 Memories
Scanning
CTCSS Encode
S Meter Squelch
Auto Power Off
Cross Band Repeat
DTMF Memory
Triple Tone Alert
DTSS Pager Function
DTMF Hand Mic

This particular unit works 100% and looks like new.  No scratches.

With paper work for $200.


Kenwood TS-700 A, 2 meter Multimode transceiver:

The Kenwood TS-700A multimode transceiver provides 2 meter
operation in FM, LSB, USB, AM and CW modes. Power output is
rated at 10 watts. It covers the entire 2 meter band.
Enhancements include RF gain, RIT, squelch, noise blanker and
44 fixed channels (11 per MHz band). Operation is from
120/220 VAC, or 13.8 VDC at 4 amps.

Features:
Multi-Mode
RIT
Noise Blanker
On-Air Indicator
Squelch
AC/DC Operation

This unit looks good. It transmits in all modes, but I am
90% sure someone took a "golden screwdriver" to it.  The
power output is in the 18 to 20 watt range instead of 11
to 12 as it should be.  This indicates some one has "tweaked"
it.  The frequency that it transmits and receives on is
not the same as indicated. Basically, I think it needs a
complete, accurate alignment, and then it would be great.

With paper work and 110 V AC power cord for $150.
The DC power cord is not included.


Linear Amp Switching Cables for Kenwood Rigs:

This cable goes from a Kenwood transceiver to a linear
amplifier to switch the amp from transmit to receive.

One end has a DIN connector, as is used with most Kenwood
rigs. The other end has an RCA phono plug, as used by most
linear amplifiers.

Before using this cable, please check the switching
capabilities of your transceiver, and the requirements
of your amplifier.

Cable for switching the T/R relay. Only $15.

Cable as above, but with ALC line in addition to T/R switching.
$20


Kenwood "Extension Feet":
This is a set of two feet that are often used on
various Kenwood rigs to raise the front by about
1/2 inch to give a rig, speaker, remote VFO, etc.
the tilt that makes it easier to read.
This is a complete set of two front feet, with the
needed hardware. $15


Other Kenwood Items, such as manuals and original boxes,
are also available.


I also have many other accessories available such as many
different types of microphones, HTs, VHF and UHF rigs, HF
and VHF/UHF antennas, connectors, miscellaneous accessories,
etc.
Just too many to list here. Please e-mail your requests.


Prices do not include shipping from Florida.

Thanks.

73,

Ken, W8EK

Ken Simpson
E-mail to W8EK at FLHam.net or W8EK at arrl.net
Voice Phone (352) 732-8400












More information about the AMRadio mailing list

This page last updated 21 Nov 2017.