[AMRadio] Alinco HF Xcvr, Desk Mic, PSs FS


Ken, W8EK kenw8ek at gmail.com
Wed Jun 1 16:46:31 EDT 2016


Alinco HF Transceiver, Desk Microphone,  and
Power Supplies For Sale


Alinco DX-70TH, HF + 6 m Transceiver:

The Alinco DX-70TH covers 160 to 6 meters in SSB, CW, AM and
FM. The receiver tunes 0.15-30 MHz and 50-54 MHz. The transmitter
delivers 100 Watts. A narrow filter and pre-amp is standard.
Other features include IF shift, dual VFOs, 100 memories, band
and memory scan, CTCSS encode, attenuator and noise blanker.

Please note that this is the "TH" model which has 100 Watts
output on 6 meters, as opposed to the "T" model that only has
10 Watts.

The DX-70TH includes the EMS-42 up-down hand mic, EBC-9
mobile mounting bracket, Owner's Manual and DC cord. It
requires 13.8 VDC at 25 Amps.

This particular unit is still in its original box. I can not
say it is new for sure, as it came from a SK, but it certainly
looks unused.

Only $450.


Alinco EMS-14 Desk Microphone:

The Alinco EMS-14 desk mic is an electret condenser mic.
The gooseneck may be adjusted to any angle. It features
UP-DOWN tuning and there is an On The Air LED on the mic
base.

On the bottom of the mic base there is a gain control
adjustment. There is also a switch for FM/SSB on the
bottom. The mic cable terminates in an Alinco round
8 pin mic plug.

Specs:
500~100K ohm.
Output 0-30mW (RMS).
Power consumption: 1.5ma RX, 2.5 ma TX.

This particular mic appears to be new, still in its original box.

These are selling in the $120 to $130 range. Buy this one
for only $90.


Astron RS-20 A, 20 amp Power Supply:

The Astron RS-20 A is a very common power supply around
most ham shacks. It provides 13 V DC for many ham rigs.

Features:
Solid State Electronically Regulated
Fold-Back Current Limiting Protects Power Supply from
...excessive current & continuous shorted output
Crowbar Over Voltage Protection
Excellent Regulation & Low Ripple at low line input voltage.
Heavy Duty Heat Sink
Chassis Mount Fuse
Three Conductor Power Cord

Specifications:
Input Voltage 105-125Vac
Output Voltage 13.8Vdc (internally Adjustable 11-15V)
Ripple Less than 5mV peak-peak (full load & low line)
Continuous Duty 16 Amps; ICS 20 Amps
Size 5" x 9" x 10-1/2"

This particular supply works great. It only varies 0.01 Volts
with a load! Cosmetically it looks great.

With paper work for only $65.


Kenwood PS-30 Power Supply:

The Kenwood PS-30 power supply provides 13.8 VDC at
20 Amps intermittent or 15 Amps continuous. It features
large heat sinks and automatic overload reset. Ripple
voltage is less than 20 mv at 13.8 V DC 20 Amps.
Input is 120 or 220 V AC.
7.2 x 5.3 x 11.5 inches

The PS-30 has two output connections. It has a 6 pin molex
connector as used on many, many Kenwood rigs, and also
on many Icom, Yaesu and Alinco rigs. In addition there
are screw terminals for lower current output, normally
used for a 2 meter or dual band rig.

This one works fine and looks great.

Paper work is included for $100.


I also have many other accessories available such as many
different types of microphones, HTs, VHF and UHF rigs, HF
and VHF/UHF antennas, connectors, miscellaneous accessories,
etc.
Just too many to list here. Please e-mail your requests.


Prices do not include shipping from Florida.

Thanks.

73,

Ken, W8EK

Ken Simpson
E-mail to W8EK at FLHam.net or W8EK at arrl.net
Voice Phone (352) 732-8400








More information about the AMRadio mailing list

This page last updated 24 Nov 2017.