From cateswa at msn.com Sat Apr 4 09:34:34 2015 From: cateswa at msn.com (Walt Cates) Date: Sat, 4 Apr 2015 08:34:34 -0500 Subject: [Hallicrafters] P-2000 transformers Message-ID: Does anyone have the resistance measurements for the transformers and chokes in the P-2000? Best Regards, Walt Cates, WD0GOF Our spoken words (or posts) are a reflection of our character. Speak often enough and you open a window to your soul. From hallicrafterssr2000 at k9axn.com Sat Apr 4 10:53:54 2015 From: hallicrafterssr2000 at k9axn.com (Jim Liles) Date: Sat, 4 Apr 2015 09:53:54 -0500 Subject: [Hallicrafters] [From Your Hallicrafters Reflector] P-2000 transformers In-Reply-To: References: Message-ID: Walt, I'll take on out of the case and measure it. Kindest regards Jim K9AXN -----Original Message----- From: Walt Cates cateswa at msn.com [HallicraftersRadios] Sent: Saturday, April 04, 2015 8:34 AM To: hallicraftersradios at yahoogroups.com ; hallicrafters Subject: [From Your Hallicrafters Reflector] P-2000 transformers Does anyone have the resistance measurements for the transformers and chokes in the P-2000? Best Regards, Walt Cates, WD0GOF Our spoken words (or posts) are a reflection of our character. Speak often enough and you open a window to your soul. __._,_.___ Posted by: Walt Cates Reply via web post ? Reply to sender ? Reply to group ? Start a New opic ? Messages in this topic (1) This site is dedicated to the free and open exchange of ideas, advice, technical and general information about Hallicrafters transmitters, receivers, home entertainment equipment, and all other Hallicrafters products. Visit Your Group New Members 1 ? Privacy ? Unsubscribe ? Terms of Use . __,_._,___ From hallicrafterssr2000 at k9axn.com Sat Apr 4 13:33:46 2015 From: hallicrafterssr2000 at k9axn.com (Jim Liles) Date: Sat, 4 Apr 2015 12:33:46 -0500 Subject: [Hallicrafters] P-2000 transformers In-Reply-To: <552000A3.5070504@shaw.ca> References: <552000A3.5070504@shaw.ca> Message-ID: <18476F76A64F45F6A87B6C7FB7CAB93A@LILESJLAPTOP> Hi Pete, Missed your response and did the deed. Thanks for the heads up, that was very good of you. Walt, Measurements: PRIMARY: Measured less than 1 ohm on all connections. Primary Inductance: BLK to BRN 150Mh @ 100 cycles BLK to GRN 280Mh @ 100 cycles WHT to BRN/YEL 150Mh @100 cycles WHT to BLK/GRN 280Mh @ 100 cycles SEC: Inductance --- resistance. HV 3.5H and 14 ohms SCREEN 1.5H 18 ohms SCREEN CHOKE: 6.3H 130 ohms Good luck and Kindest regards Jim K9AXN -----Original Message----- From: 'Peter Shilton, VE7PS' ve7ps at shaw.ca [HallicraftersRadios] Sent: Saturday, April 04, 2015 10:17 AM To: Jim Liles ; Walt Cates ; hallicraftersradios at yahoogroups.com ; hallicrafters Subject: Re: [From Your Hallicrafters Reflector] P-2000 transformers Jim: I emailed Walt separately already - mine is out of the case so no need to do that with yours unless Walt needs it right away. I won't be back home until Monday afternoon. 73 Peter VE7PS On 4/4/2015 7:53 AM, 'Jim Liles' hallicrafterssr2000 at k9axn.com [HallicraftersRadios] wrote: Walt, I'll take on out of the case and measure it. Kindest regards Jim K9AXN -----Original Message----- From: Walt Cates cateswa at msn.com [HallicraftersRadios] Sent: Saturday, April 04, 2015 8:34 AM To: hallicraftersradios at yahoogroups.com ; hallicrafters Subject: [From Your Hallicrafters Reflector] P-2000 transformers Does anyone have the resistance measurements for the transformers and chokes in the P-2000? Best Regards, Walt Cates, WD0GOF Our spoken words (or posts) are a reflection of our character. Speak often enough and you open a window to your soul. __._,_.___ Posted by: "Peter Shilton, VE7PS" Reply via web post ? Reply to sender ? Reply to group ? Start a New opic ? Messages in this topic (3) This site is dedicated to the free and open exchange of ideas, advice, technical and general information about Hallicrafters transmitters, receivers, home entertainment equipment, and all other Hallicrafters products. Visit Your Group New Members 1 ? Privacy ? Unsubscribe ? Terms of Use . __,_._,___ From wa6aaj at gmail.com Thu Apr 9 12:35:20 2015 From: wa6aaj at gmail.com (Mike Kennedy) Date: Thu, 9 Apr 2015 09:35:20 -0700 Subject: [Hallicrafters] FS: SX-115 Receiver In-Reply-To: References: Message-ID: Excellent cosmetics and operating condition. Copy of manual. You will be hard pressed to find a better one. If seriously interested I can send pics during the evening. $1200 Plus shipping Thanks Mike From wa6aaj at gmail.com Mon Apr 13 11:56:53 2015 From: wa6aaj at gmail.com (Mike Kennedy) Date: Mon, 13 Apr 2015 08:56:53 -0700 Subject: [Hallicrafters] FS: SX-115 RECEIVER Message-ID: Excellent operating and cosmetic condition. $1200 plus shipping. Pics available for serious inquiries. Thanks Mike From hallicrafters at mailman.qth.net Fri Apr 17 00:43:25 2015 From: hallicrafters at mailman.qth.net (Joe Connor via Hallicrafters) Date: Fri, 17 Apr 2015 04:43:25 +0000 (UTC) Subject: [Hallicrafters] test Message-ID: <734280188.2713392.1429245805046.JavaMail.yahoo@mail.yahoo.com> I've been having trouble receiving messages from the list. I just want to test it. Joe Connor From rbethman at comcast.net Fri Apr 17 07:59:51 2015 From: rbethman at comcast.net (rbethman) Date: Fri, 17 Apr 2015 07:59:51 -0400 Subject: [Hallicrafters] test In-Reply-To: <734280188.2713392.1429245805046.JavaMail.yahoo@mail.yahoo.com> References: <734280188.2713392.1429245805046.JavaMail.yahoo@mail.yahoo.com> Message-ID: <5530F5B7.30805@comcast.net> Joe, Test good! Regards, Bob - N0DGN On 4/17/2015 12:43 AM, Joe Connor via Hallicrafters wrote: > I've been having trouble receiving messages from the list. I just want to test it. > Joe Connor From hallicrafters at mailman.qth.net Fri Apr 17 09:47:56 2015 From: hallicrafters at mailman.qth.net (Joe Connor via Hallicrafters) Date: Fri, 17 Apr 2015 13:47:56 +0000 (UTC) Subject: [Hallicrafters] test In-Reply-To: <5530F5B7.30805@comcast.net> References: <5530F5B7.30805@comcast.net> Message-ID: <148936881.5104225.1429278476039.JavaMail.yahoo@mail.yahoo.com> Thanks, guys. For some unknown reason, I had been excommunicated from the group. When I tried to post or re-join, I was getting weird messages that even Duane did not understand. Finally, I apparently pushed the right sequence of buttons and was able to re-join. I missed the list, because the posts are interesting and I always learn something. Joe Connor On Friday, April 17, 2015 8:01 AM, rbethman wrote: Joe, Test good! Regards, Bob - N0DGN On 4/17/2015 12:43 AM, Joe Connor via Hallicrafters wrote: > I've been having trouble receiving messages from the list. I just want to test it. > Joe Connor ______________________________________________________________ Hallicrafters mailing list Home: http://mailman.qth.net/mailman/listinfo/hallicrafters Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Hallicrafters at mailman.qth.net List Administrator: Duane Fischer, W8DBF ** For Assistance: dfischer at usol.com ** This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html From wa6aaj at gmail.com Thu Apr 23 11:40:38 2015 From: wa6aaj at gmail.com (Mike Kennedy) Date: Thu, 23 Apr 2015 08:40:38 -0700 Subject: [Hallicrafters] Test Message-ID: From w6zkh at att.net Thu Apr 23 14:34:36 2015 From: w6zkh at att.net (John Neeley) Date: Thu, 23 Apr 2015 18:34:36 +0000 (UTC) Subject: [Hallicrafters] HT-32a Zero Beating Message-ID: <634497106.1493616.1429814076437.JavaMail.yahoo@mail.yahoo.com> How do you zero beat the HT-32a TX with the receiver?? I tried the Calibrate mode which didnt do nothing for me.? The manual is very vague on this subject.? I am using a SX-101a as a receiver, and in doing so, I utilize the VOX relay in the TX to switch Pin 7 on the accessory plug on the RX from Gnd to Open, on PTT.? When the relay (pin 7) goes Open, it disables the receiver audio, thereby unable to hear any zero beat.? Is there a SECRET method??? Any help would be appreciated. John W6ZKH From rbethman at comcast.net Thu Apr 23 15:14:48 2015 From: rbethman at comcast.net (rbethman) Date: Thu, 23 Apr 2015 15:14:48 -0400 Subject: [Hallicrafters] HT-32a Zero Beating In-Reply-To: <634497106.1493616.1429814076437.JavaMail.yahoo@mail.yahoo.com> References: <634497106.1493616.1429814076437.JavaMail.yahoo@mail.yahoo.com> Message-ID: <553944A8.7080802@comcast.net> John, It has been a number of years since I've operated that specific pairing. IIRC, when the TX is in calibrate mode, you will need to flip the SX-101A Send/Rcv switch to Recv. TX in AM, and Rx in DSB. DO NOT key the transmitter! The receiver in its receive mode and will get the center carrier heard, leaving you to simply center and Zero Beat the receiver. Then you can get the two in sync with each other. The other option is to plug into the jack on top of the final cage, and run a wire "near" the receiver antenna connector. Regards, Bob - N0DGN On 4/23/2015 2:34 PM, John Neeley wrote: > How do you zero beat the HT-32a TX with the receiver? I tried the Calibrate mode which didnt do nothing for me. The manual is very vague on this subject. I am using a SX-101a as a receiver, and in doing so, I utilize the VOX relay in the TX to switch Pin 7 on the accessory plug on the RX from Gnd to Open, on PTT. When the relay (pin 7) goes Open, it disables the receiver audio, thereby unable to hear any zero beat. Is there a SECRET method?? Any help would be appreciated. > John W6ZKH From anchor at ec.rr.com Thu Apr 23 16:11:57 2015 From: anchor at ec.rr.com (Al Parker) Date: Thu, 23 Apr 2015 16:11:57 -0400 Subject: [Hallicrafters] HT-32a Zero Beating In-Reply-To: <634497106.1493616.1429814076437.JavaMail.yahoo@mail.yahoo.com> References: <634497106.1493616.1429814076437.JavaMail.yahoo@mail.yahoo.com> Message-ID: <5539520D.20702@ec.rr.com> Hi John, Bob, et al, I operate my HT-32 (not A, but should be exactly the same here) and SX-115 weekly. All you need to do to zero beat is flip the operation switch on the xmtr to "Cal", and leave the PTT alone, the rcvr listening normally. You probably will have to increase the "Calibrate Level" pot so you can hear the signal. I have my level at about 6 on 20m. It probably assumes you have at least the driver stage peaked on the band you are on. hope this works for you, 73, Al, W8UT www.boatanchors.org www.hammarlund.info "There is nothing -- absolutely nothing -- half so much worth doing as simply messing about in boats" Ratty, to Mole On 4/23/2015 2:34 PM, John Neeley wrote: > How do you zero beat the HT-32a TX with the receiver? I tried the Calibrate mode which didnt do nothing for me. The manual is very vague on this subject. I am using a SX-101a as a receiver, and in doing so, I utilize the VOX relay in the TX to switch Pin 7 on the accessory plug on the RX from Gnd to Open, on PTT. When the relay (pin 7) goes Open, it disables the receiver audio, thereby unable to hear any zero beat. Is there a SECRET method?? Any help would be appreciated. > John W6ZKH > ______________________________________________________________ > Hallicrafters mailing list > Home: http://mailman.qth.net/mailman/listinfo/hallicrafters > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Hallicrafters at mailman.qth.net > > List Administrator: Duane Fischer, W8DBF > ** For Assistance: dfischer at usol.com ** > > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > From w6zkh at att.net Thu Apr 23 20:32:02 2015 From: w6zkh at att.net (John Neeley) Date: Fri, 24 Apr 2015 00:32:02 +0000 (UTC) Subject: [Hallicrafters] HT-32a Zero Beating Message-ID: <137816824.1620357.1429835522935.JavaMail.yahoo@mail.yahoo.com> Thanks to you fellows for giving me the CORRECT METHOD on how to zero beat this beast.... it does work, but had to run the Calibrate knob up to about 8 or so to hear it on the receiver....? The manual was very vague to say the least....or I am being a early ALZ's patient at 73, hi...? Again, thanks for the info and help, duely appreciated for sure. John W6ZKH

This page last updated 26 Jul 2017.